We Support Their Performance.Not Just Their Installation.
Engineering support beyond installation — preventive maintenance, AMC, membrane cleaning and replacement, performance evaluation and troubleshooting, for everything from a kitchen purifier to a plant room.
Engineering Support Beyond Installation
We Don’t Just Install Plants.We Support Their Performance.
Scheduled checks against the plant's operating history, not a generic calendar.
Annual contracts covering visits, consumables and response commitments.
Attending faults on domestic, commercial and industrial systems.
Media change-out for sand, carbon and softening vessels.
RO membrane replacement sized and specified for the installed array.
Clean-in-place to recover performance before replacement becomes necessary.
Cartridges, media, dosing chemicals and spares for installed systems.
Measuring what the plant is actually delivering against what it was designed to.
Re-engineering an existing plant when demand, feed water or output quality has changed.
Diagnosing why the water or the plant is not behaving as expected.
Three Scopes,Matched to the Plant.
An annual contract is scoped to what is actually installed. A kitchen purifier and a plant room do not need the same visit, and should not be sold the same contract.
Home Purifier AMC
For domestic RO, RO+UV and dispenser installations in and around Salem.
- Scheduled preventive visits
- Filter and cartridge replacement
- Membrane replacement when due
- Breakdown attendance
- Water quality check at each visit
Visit frequency, response commitments and pricing are set per contract.
Commercial Plant AMC
For 100–1000 LPH commercial RO and the pre-treatment train feeding it.
- Everything in the domestic scope
- Media replacement for sand and carbon vessels
- Softener regeneration check and salt consumption review
- RO membrane cleaning (CIP)
- Performance evaluation against design output
- Consumables and spares supply
Visit frequency, response commitments and pricing are set per contract.
Engineered Plant Support
For industrial RO, WTP, DM, STP, ETP and healthcare water systems.
- Everything in the commercial scope
- Dosing system review and chemical supply
- Loop sanitisation for healthcare systems
- Troubleshooting on output quality and recovery
- Plant upgradation where demand or feed water has changed
- Long-term technical support
Visit frequency, response commitments and pricing are set per contract.
Something not working as it should?
Tell us what the system is doing — low output, poor taste, rising TDS, a plant that will not hold its recovery — and what is installed. Diagnosing it properly is usually cheaper than replacing a part that was never the problem.
Before You Buy Anything.
The most common questions we are asked, answered the way we would answer them on the phone. If the honest answer is “you may not need RO”, that is what it says.
Ask a Water EngineerIt depends on your source and its dissolved-solids load. Municipal supply at moderate TDS is usually served by an RO or RO+UV system; borewell water with hardness often needs softening ahead of the purifier. If you are unsure, start with the water problem finder or send us a water analysis report.
Not always. RO addresses dissolved solids. If your issue is microbiological or particulate rather than dissolved load, UF or UV may be the correct answer, and RO would remove minerals unnecessarily. We recommend based on the analysis, not by default.
RO uses a semi-permeable membrane to remove dissolved solids. UF is a membrane filtration that removes suspended matter and microbiological load while leaving dissolved minerals in place. UV disinfects without removing anything physically. Many systems use them together, each doing the job it is suited to.
Yes. Water analysis is the first step of every engineered solution we deliver. You can also send an existing analysis report with your enquiry and we will design against it.
Borewell water in this region commonly carries hardness, and sometimes iron. That usually means pre-treatment ahead of the RO rather than a bigger RO. The specific configuration follows from the analysis.
Yes. Installation is available for domestic products, and installation and commissioning are part of every commercial, industrial and healthcare project.
Yes. AMC programs cover preventive maintenance visits, consumables and breakdown response, scoped to the system installed.
Yes — from entry-level 100 LPH skids through to 1000 LPH systems with full pre-treatment trains, for hotels, canteens, institutions and commercial buildings.
Yes. Industrial RO plants are designed from the source-water analysis, the quality the process requires and the capacity and recovery the site needs.
Yes. We engineer hemodialysis RO systems including the distribution loop and disinfection regime, as well as portable single-station units.
A high-recovery RO plant is designed so that a larger share of the feed water leaves as usable permeate rather than reject. We design plants capable of reaching up to 75% recovery where feed-water conditions permit. Recovery depends on source-water characteristics and system design.
Yes, for appropriate non-potable applications. STP and ETP systems can be designed with reuse as the target — flushing, gardening, cooling make-up — rather than treating only to a discharge limit.
Ready to start from your water?
Whether you are looking for a home purifier or planning an industrial plant room, our engineering team is in Salem.
Or call us directly — +91 99438 46677